Free domestic shipping from €99 *

  Collection of stretcher frame strips and fabrics is not possible on Saturdays!

  Free domestic shipping from €99 *

  Collection of stretcher frame strips and fabrics is not possible on Saturdays!

Go to homepage
€0.00*

Wir wollen unseren Kunden höchste Qualität anbieten. Daher produzieren wir unsere Keilrahmen aus 100% Kiefernholz aus polnischen Wäldern. Im Gegensatz zu anderen Herstellern verwenden wir bewußt nicht abgeharztes Holz, da diesesweniger anfällig ist für die Aufnahme von Feuchtigkeit und sich daher weniger leichter verzieht. Kiefernholz, das sein natürliches Harz noch enthält, ist zwar etwas schwerer, bietet aber unserer Erfahrung nach wesentlich mehr Stabilität. Um diese Stabilität zusätzlich zu gewährleisten, produzieren wir keine Leisten, die unter einer Tiefe von 20mm liegen. Rahmen mit einer Tiefe von 15-18 mm sind erfahrungsgemäß schneller verziehen.

Die Keilrahmenleisten mit dem Profil K30, K40, K60 und K70 enthalten ab einer Länge von 50 cm einen Schlitz für ein Mittelstück und ab 200 cm einen Doppelschlitz. Die Profile K65, K6570 und K10070 haben ab 60 cm einen Schlitz, ab 2 m einen Doppel- Schlitz, ab 300 cm einen 3-fach Schlitz und ab 400cm einen 4-fach Schlitz. Gleiches gilt für die Mittelstücke. Bitte sprechen Sie uns bei Bedarf auf Übergrößen und verfügbare Profile an.

Für die Rahmengrößen gelten folgende Standards:

  • 50 x 50cm ohne Mittelstück
  • 60 x 60cm bis 90 x 90cm ein Mittelstück
  • 100 x 100cm bis 195 x 195cm einfaches Kreuz

Ab einer Leisten-Länge von 2m enpfehlen wir ein Doppelkreuz, d.h. ein Mittelstück über die längere Seite und zwei Mittelstücke für die kürzere Seite der Leisten.

  • 2 x 2m bis 2,90 x 2,90m Doppel-Doppel-Kreuz
  • 3 x 3m bis 3,90 x 3,90m Drei-auf-Drei Mittelstücke
  • 4 x 4m bis 4,90 x 4,90m Vier-auf-Vier Mittelstücke

 

 

Weitere Besonderheiten:

Alle Leisten der Profilgrößen K30, K35, K40, K45 und K2060 bestehen aus in einander gesteckten Holz-Teilen und haben eine runde Kante.

Die Profilgrößen K65, K70, K6570 und K10070 sind mehrfach verleimt und daher besonders stabil. Dies ist gerade für großformatige Rahmen von Vorteil. Die Profile haben nach der Bespannung aufgrund der scharfen Kante mehr Spielraum zwischen Leinwand und Leiste.

 

Filter
Tip
stretcher bar K45 ( 2.0 x 4.5 cm )
stretcher bar K45 ( 2.0 x 4.5 cm )
      profile: 2.0 x 4.5 cm     side length 15 - 300 cm     custom formats possible on request     `sharp edge' possible on request The K 45 has a profile of 2.0 x 4.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 15 to 300 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The pine wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/910/standard-wedges/keys-pine-50-pcs If you require an additional bracing, please combine the frame with the cross bars K 45: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/12/cross-brace-k45-and-k40?number=10012The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 50cm no middle bars are needed. If one side length exceeds 50cm, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross).

Content: 0.15 Laufende(r) Meter (€2.73* / 1 Laufende(r) Meter)

From €0.41*
Details
stretcher bar K35 ( 2.0 x 3.5 cm )
stretcher bar K35 ( 2.0 x 3.5 cm )
      profile: 2.0 x 3.5 cm     side length 15 - 160 cm     custom formats possible on request     `sharp edge' possible on request The K35 has a profile of  2.0 x 3.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 15 to 80 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge of 5 euros per bar.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The pine wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/910/wedges-standard-pine/keys-100pcs?number=10864 If you require an additional bracing, please combine the frame with the cross bars K35: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/34/keilrahmen-mittelstueck-k35-1-8x3-5cm?number=10034The stretcher frame has a 1-fold slit from a side length of 50 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross).  

Content: 0.15 Laufende(r) Meter (€1.87* / 1 Laufende(r) Meter)

From €0.28*
Details
STANDARD wedges / keys, pine, 50 pcs
STANDARD wedges / keys, pine, 50 pcs
    wedges made of pine wood     100 pieces     suitable for stretcher frame K35 and K40     Dimensions 65 x 23 x 4mm

€3.00*
cross brace K45 and K40
cross brace K45 and K40
The middle bars K 45 are suitable for both stretcher frames K 40 and K 45.From 50 cm length one slit, i.e. a middle bars or a cross. From 2 m length two slots, i.e. two middle bars per side or a double double cross. Depending on the length, the centre pieces either have no slot at all (shorter than 50 cm length), only one slot (from 50 cm length) or 2 slots (from 2m length). Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there.The length of the center element should correspond to the length of the sidebar. Example: for a frame measuring 100x100 cm you need two center pieces in size 100 cm (simple cross).

Content: 0.3 Laufende(r) Meter (€2.73* / 1 Laufende(r) Meter)

From €0.54*
Details
stretcher bar K40 ( 4.0 x 4.5 cm )
stretcher bar K40 ( 4.0 x 4.5 cm )
    profile: 4.0 x 4.5 cm     side length 18 - 350 cm     custom formats possible on request     `sharp edge' possible on request The K 45 has a profile of 4.0 x 4.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 18 to 350 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The pine wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/991/big-wedges/keys-beech-50-pcs. If you require an additional bracing, please combine the frame with the cross bars K 45: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/12/cross-brace-k45-and-k40?number=10012The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 60cm no middle bars are needed. If one side length exceeds 60cm, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross). The length of the center element should correspond to the length of the sidebar. Example: for a frame measuring 100x100 cm you need two center pieces in size 100 cm (simple cross).

Content: 0.2 Laufende(r) Meter (€5.45* / 1 Laufende(r) Meter)

From €1.09*
Details
stretcher bar K30 (2.8 x 4.5 cm)
stretcher bar K30 (2.8 x 4.5 cm)
    profile: 2.8 x 4.5 cm     side length 20 - 300 cm     custom formats possible on request     `sharp edge' possible on request The K30 has a profile of 2.8 x 4.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 20 to 300 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The pine wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please orderhttps://peters-art.de/en/Painting-Supports/Stretchers/Wooden-Stretchers/910/STANDARD-wedges/keys-pine-50-pcsIf you require an additional bracing, please combine the frame with the cross bars K30: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/32/keilrahmen-mittelstueck-k30-1-8-x-4-5cm?number=10032The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross).The length of the middle bar should correspond to the length of the side strips. Example: for a frame measuring 100x100 cm, you need two middle bars measuring 100 cm (simple cross).

Content: 0.2 Laufende(r) Meter (€4.25* / 1 Laufende(r) Meter)

From €0.85*
Details
stretcher bar K60 ( 2.5 x 6.0 cm )
stretcher bar K60 ( 2.5 x 6.0 cm )
    profile: 2.5 x 6.0 cm     side length 25 - 400 cm     custom formats upon request     `sharp edge' upon request The K 60 has a profile of  2.5 x 6.0 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 25 to 400 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The hard wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/991/wedges-big-beech/keys-50pcs.?number=10939 If you require an additional bracing, please combine the frame with the cross bars K60: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/30/cross-brace-k60?number=10030 The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross). The length of the center element should correspond to the length of the sidebar. Example: for a frame measuring 100x100 cm you need two center pieces in size 100 cm (simple cross).

Content: 0.3 Laufende(r) Meter (€4.70* / 1 Laufende(r) Meter)

From €1.21*
Details
cross brace K35 (1,8 x 3,5 cm)
cross brace K35 (1,8 x 3,5 cm)
    from 50 cm lengthone slit,   i.e. a middle bars or a cross: from 2 m lengthtwo slots,i.e. two middle bars per side or a double double cross:         Depending on the length, the centre pieces either have no slot at all (shorter than 50 cm length), only one slot (from 50 cm length) or 2 slots (from 2m length). Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there.    

Content: 0.3 Laufende(r) Meter (€1.87* / 1 Laufende(r) Meter)

From €0.56*
Details
cross brace K60 ( 1,6 x 5,5 cm)
cross brace K60 ( 1,6 x 5,5 cm)
   The middle bars K60 are suitable for stretcher frames K60. Depending on the length, the centre pieces either have no slot at all (shorter than 50 cm length), only one slot (from 50 cm length) or 2 slots (from 2m length). Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there. The length of the central element should correspond to the length of the side strips. Example: for a frame measuring 100x100 cm, you need two central pieces measuring 100 cm (simple cross).

Content: 0.3 Laufende(r) Meter (€4.70* / 1 Laufende(r) Meter)

From €1.41*
Details
stretcher bar K65 ( 2.7 x 7.0 cm )
stretcher bar K65 ( 2.7 x 7.0 cm )
Profile: 2.7 x 7.0 cm Side length 30 – 300 cm Cutting to desired formats possiblestandard sharp edgefrom 3 m 3-fold slotted The K65 has a profile of 2.7 x 7.0 cm. We use seasoned and kiln-dried pine wood for the stretcher frame. The wood is finger-galvanized to prevent the wood's natural tendency to warp and, thanks to multiple gluing, is almost warp-free - a high-quality handcrafted product at an extremely affordable price. The stretcher frame is available with a side length of 30 to 300 cm. On request, we can produce stretcher bars of any length; the production time is usually 7-10 days. Please email questions about custom-sized stretcher frames. The stretcher frame has a sharp edge as standard. To get a stretcher frame, you need two stretcher bars on the long side, two on the shorter side and possibly a middle piece or cross and wedges. The stretcher frame comes with a single slot from a side length of 60 cm up to a side length of 195 cm, a double slot from a side length of 200 cm and a triple slot with a side length of 300 cm. Note on reinforcement: With a side length of 60cm you do not need any middle pieces. If a side length exceeds 60cm, a middle piece of the shorter side length is sufficient. If both sides are over 1m long, you need a middle piece per side length (i.e. a simple cross). If one side is over 2m long, you need two center pieces on the shorter side and one on the long side (simple double cross). If both sides are over 2m long, the strips each have double slots, so you need two middle pieces per side length (double double cross). With this profile, strips over 3m long have three slots. Please select the appropriate number of centerpieces. The length of the center element should correspond to the length of the sidebar. Example: for a frame measuring 100x100 cm you need two center pieces in size 100 cm (simple cross).

Content: 0.3 Laufende(r) Meter (€12.70* / 1 Laufende(r) Meter)

From €3.81*
Details
cross brace K30 ( 1,8 x 4,5 cm)
cross brace K30 ( 1,8 x 4,5 cm)
Depending on the length, the centre pieces either have no slot at all (shorter than 50 cm length), only one slot (from 50 cm length) or 2 slots (from 2m length). Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there.

Content: 0.3 Laufende(r) Meter (€3.07* / 1 Laufende(r) Meter)

From €0.92*
Details
BIG wedges / keys, beech, 50 pcs.
BIG wedges / keys, beech, 50 pcs.
    wedges made of beech wood     50 pieces     suitable for stretcher frame K30, K40, K60, K2060 and middle bar K65     dimmensions: 75 x 25 x 4mm

€7.00*
stretcher bar K70 ( 4.5 x 7.0 cm )
stretcher bar K70 ( 4.5 x 7.0 cm )
profile: 4.5 x 7.0 cm     side length 30 - 500 cm     custom formats upon request    sharp edge as standard     from 3 m 3-fold slotted, from 4 m 4-fold slotted The K 70 has a profile of 4.5 x 7.0 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 30 to 500 cm. On request we can produce stretcher bars in any length, the production time is usually 7-10 days. Questions about custom size bars please send by email.The stretcher frame has a sharp edge as standard.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The hard wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order for the stretcher bars and the cross braces https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/918/wedges-big-k70/keys-50pcs.?number=10872 If you require an additional bracing, please combine the frame with the cross bars K70: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/17/cross-brace-for-k70-and-k6570-7-0x4-5cm?number=10017 The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm, a 2-fold slit from a side length of 200 cm, a 3-fold slit with a side length of 300 cm and a 4-fold slit from a side length of 400 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross). With this profile, bars are triple slotted over 3m length and quadruple slotted over 4m length. Please select the appropriate number of middle pieces. The length of the center element should correspond to the length of the sidebar. Example: for a frame measuring 100x100 cm you need two center pieces in size 100 cm (simple cross).

Content: 0.3 Laufende(r) Meter (€17.27* / 1 Laufende(r) Meter)

From €5.18*
Details
cross brace K65 ( 1,8 x 7 cm)
cross brace K65 ( 1,8 x 7 cm)
from 60 cm lenght one slot from 2 m lenght two slot from 3 m length 3 slots from 4 m length 4 slots Depending on the length, the centre pieces either have no slot at all (shorter than 60 cm length), only one slot (from 60 cm length) or 2 slots (from 2m length),  from 3 m length 3 slots,  from 4 m length 4 slots. Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there. The length of the central element should correspond to the length of the side bar. Example: For a frame measuring 100x100 cm, you need two central elements measuring 100 cm (single cross).

Content: 0.4 Laufende(r) Meter (€12.70* / 1 Laufende(r) Meter)

From €2.17*
Details
cross brace for K70 and K6570 (7,0 x 4,5cm)
cross brace for K70 and K6570 (7,0 x 4,5cm)
from 60 cm lenght one slot from 2 m lenght two slot from 3 m length 3 slots from 4 m length 4 slots   Depending on the length, the centre pieces either have no slot at all (shorter than 60 cm length), only one slot (from 60 cm length) or 2 slots (from 2m length),  from 3 m length 3 slots,  from 4 m length 4 slots. Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there. The length of the central element should correspond to the length of the side strips. Example: for a frame measuring 100x100 cm, you need two central pieces measuring 100 cm (simple cross).

Content: 0.4 Laufende(r) Meter (€17.25* / 1 Laufende(r) Meter)

From €6.90*
Details
wedges / keys K65, beech, 50 pcs.
wedges / keys K65, beech, 50 pcs.
    wedges made of beech wood     50 pieces     suitable for stretcher frame K65     for middle bar K65 please order: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/991/wedges-big-beech/keys-50pcs.?number=10939     dimmensions 95 x 30 x 5mm

€8.00*
wedges / keys K70, beech, 50 pcs.
wedges / keys K70, beech, 50 pcs.
      wedges made of beech wood     50 pieces     suitable for stretcher frameK70, K6570, K10070 and middle bar K70     dimmensions 97 x 30 x 7mm  

€14.00*
stretcher bar K2040 ( 2.0 x 4 cm )
stretcher bar K2040 ( 2.0 x 4 cm )
    profile: 2.0 x 4 cm     side length 25 - 400 cm     custom formats upon request     ´sharp edge´ upon request     from 2 m 2-fold slit     only available on order, e.g. by e-mail The K 2040 has a profile of  2.0 x 4 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 25 to 400 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge of 5 euros per bar.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The hard wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order for the stretcher bars and the cross braces https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/991/wedges-big-beech/keys-50pcs.?number=10939 If you require an additional bracing, please combine the frame with the cross bars K2060: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/2342/stretcher-bar-k60?number=12239 The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross). Please select the appropriate number of middle bars.    

Content: 0.2 Laufende(r) Meter (€1.05* / 1 Laufende(r) Meter)

From €0.19*
Details
SMALL wedges / keys, beech, 50 pcs.
SMALL wedges / keys, beech, 50 pcs.
    wedges made of beech wood     50 pieces     suitable for stretcher frame K30, K40, K45, K60, K2060 and middle bar K65     dimmensions: 60 x 20 x 4mm

€5.00*
%
stretcher bar K2065 ( 2.0 x 6.5 cm )
stretcher bar K2065 ( 2.0 x 6.5 cm )
    profile: 2.0 x 6.5 cm     side length 25 - 400 cm     custom formats upon request     ´sharp edge´ upon request     from 2 m 2-fold slit     only available on order, e.g. by e-mail The K 2065 has a profile of  2.0 x 6.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 25 to 400 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The hard wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order for the stretcher bars and the cross braces https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/991/wedges-big-beech/keys-50pcs.?number=10939 If you require an additional bracing, please combine the frame with the cross bars K2065: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/2342/stretcher-bar-k60?number=12239 The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross). Please select the appropriate number of middle bars.      

Content: 0.25 Laufende(r) Meter (€3.64* / 1 Laufende(r) Meter)

From €0.91* €1.19* (23.53% saved)
Details
Uncovered Circular stretcher, Tondo
Uncovered Circular stretcher, Tondo
Our circles are made of plywood and have a standard depth of 18mm, i. e. 15mm plus 3mm edge. Other depths are possible at any time, for example 36mm or 45mm. We are happy to add additional centerpieces or crosses for oversized circles and ovals.   We also offer a canvas stretching service for our circles.   Of course we also produce framing for the circles in our own workshop.   The frames are made of MDF board for the standard depth of 18cm and up to a size of 80cm. We do not recommend larger framing, otherwise it’s susceptible to break in our experience.   Special features circles   Depending on the production method, the circles have a width of 4cm (smaller formats), which are made of one piece of wood or 5cm (larger formats), which were glued together.   Our smallest circle has a diameter of 12cm. With the maximum size there’s almost no limits to your ideas. Whether 2m, 2.50m or 3m, we gladly manufacture your desired size. Price examples can be found in our online shop.  

From €3.30*
Details
Oval stretcher
Oval stretcher
Our ovals are made of blockboard * and have a standard depth of 18mm, i. e. 15mm plus 3mm edge. Other depths are possible at any time, for example 36mm or 45mm. We are happy to add additional centerpieces or crosses for oversized circles and ovals.   We also offer a canvas stretching service for our ovals.   Of course we also produce framing for the ovals in our own workshop.   The frames are made of MDF board for the standard depth of 18cm and up to a size of 80cm. We do not recommend larger framing, otherwise it’s susceptible to break in our experience.     Special features ovals   Our ovals are shown in 2 dimensions: width and length. Unlike the circles, the depth of production is 6cm on the long sides of the ovals and 4cm on the shorter sides.   Our smallest ovals have a width of 12cm and a length of 14cm. With the maximum size  there’s almost no limits to your ideas. Whether 2m, 2.50m or 3m, we gladly manufacture your desired size. Price examples can be found in our online shop.   *Blockboard is very light due to its low density and dimensionally stable even under fluctuating climatic conditions, it’s rigid and has a high endurance, i.e. deforms only a little.  

From €12.00*
Details
%
cross brace K2065 ( 2,0 x 5,5 cm)
cross brace K2065 ( 2,0 x 5,5 cm)
   The middle bars K2065 are suitable for stretcher frames K2065.   Depending on the length, the centre pieces either have no slot at all (shorter than 50 cm length), only one slot (from 50 cm length) or 2 slots (from 2m length). Accordingly, further middle pieces should be added so that 2 of them interlock at each slot, forming a cross and thus stabilizing the frame. Matching slots are worked into the wedge frames to anchor the ends of the corresponding centre pieces there.  

Content: 0.3 Laufende(r) Meter (€4.00* / 1 Laufende(r) Meter)

From €1.20* €1.41* (14.89% saved)
Details
stretcher bar K30 ( 3.0 x 4.5 cm)
stretcher bar K30 ( 3.0 x 4.5 cm)
    profile: 3.0 x 4.5 cm     side length 20 - 300 cm     custom formats possible on request     `sharp edge' possible on request The K30 has a profile of 3.0 x 4.5 cm. We use seasoned and kiln-dried pine for the stretcher frame. The wood is finger-jointed to prevent the natural tendency of the wood to warp and, thanks to multiple gluing, is almost free of warping- a high-quality handcrafted product at an extraordinarily affordable price.The stretcher frame is available from a side length of 20 to 300 cm. We will be happy to cut the frame to your desired format for an additional charge of 5 euros per bar. Please note that the cross bars must also be cut to size.The stretcher frame has a round edge. If you wish a 'sharp edge', it is possible against a surcharge of 5 euros per bar.In order to obtain a stretcher frame, you need two stretcher bars of the long side, two of the shorter side and optionally a middle piece or cross and wedges.The pine wood wedges necessary for wedging (2 pieces per bar and middle bar) are not included in the price. Please order https://peters-art.de/de/malgruende/keilrahmen/holz-keilrahmen/910/keile-standard-kiefer-100-stueck?number=10864 If you require an additional bracing, please combine the frame with the cross bars K30: https://peters-art.de/en/painting-supports/stretchers/wooden-stretchers/32/keilrahmen-mittelstueck-k30-1-8-x-4-5cm?number=10032The stretcher frame has a 1-fold slit from a side length of 50 cm up to a side length of 195 cm and a 2-fold slit from a side length of 200 cm.Advice on bracing:Under a side length of 1m no middle bars are needed. If one side length exceeds 1m, one middle bar of the shorter side length is sufficient.If both sides are more than 1m long, you need one bar per side length (a simple cross). If one side is more than 2m long, you need two middle pieces of the shorter side and one of the long side (single double cross). If both sides are more than 2m long, the stretcher bars are each double slotted, so you need two middle bars per side length (double double cross).    

Content: 1.85 Laufende(r) Meter (€1.54* / 1 Laufende(r) Meter)

From €3.08*
Details
This website uses cookies to ensure the best experience possible. More information...